A unified theory for brittle and ductile shear mode fracture

A unified theory captures both brittle and ductile fracture. The fracture toughness is proportional to the applied stress squared and the length of the crack. For purely brittle solids, this criterion is equivalent to Griffith's theory. In other cases, it provides a theoretical basis for the Irwin-Orowan formula. For purely ductile solids, the theory makes direct contact with the Bilby-Cottrell-Swinden model. The toughness is highest in ductile materials because the shielding dislocations in the plastic zone provide additional resistance to crack growth. This resistance is the force opposing dislocation motion, and the Peach-Koehler force overcomes it. A dislocation-free zone separates the plastic zone from and the tip of the crack. The dislocation-free zone is finite because molecular forces responsible for the cohesion of the surfaces near the crack tip are not negligible. At the point of crack growth, the length of the dislocation-free zone is constant and the shielding dislocations advance in concert. As in Griffith's theory, the crack is in unstable equilibrium. The theory shows that a dimensionless variable controls the elastoplastic behaviour. A relationship for the size of the dislocation-free zone is derived in terms of the macroscopic and microscopic parameters that govern the fracture.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

The deformation and fracture of balloons

Inflation of balloons provides a straightforward way of achieving large biaxial deformations. Previous studies have shown that when a balloon bursts, crack propagation occurs at very high speed – much higher than would be expected from the low strain modulus and elastic wave velocity of the rubber. The present paper is concerned with studies of the deformation and fracture of cylindrical balloons. On inflation, the deformations of such a balloon pass through an unstable region but subsequently increase monotonically with pressure. In this relatively high pressure region, the ratio of the longitudinal and circumferential extension ratios is broadly in accord with expectations from high-strain elasticity theory when the ratio of the corresponding stresses is taken into account. On bursting, crack speeds up to around 300 m/s in this region. It is shown that these speeds are in accord with large increase in incremental moduli for the highly-strained rubber. Marked changes in crack tip profile observed at very high crack speeds are consistent with control of the rate of growth by inertia rather than by the viscoelastic properties of the rubber (as is believed to be the case at lower speeds). Consistent with this, various elastomers having different glass transition temperatures show similar crack growth behaviour in the very high speed region.     

A novel specimen for investigating the mechanical behavior of elastomers under multiaxial loading conditions

In this paper we describe the design and manufacture of an axial-torsion test specimen, and provide relationships needed when conducting stress-strain characterization experiments with the specimen. The specimen is a short hollow cylinder of rubber bonded between two steel mounting rings, in which simultaneous axial and shear strains are produced via independently controlled axial and twist displacements. We present calculations for the strain-displacement and stress-load relationships, and strain energy density. These relationships have been established and validated via a combination of analytical and experimental techniques, and finite element analysis. We have investigated the extent and effects of strain and stress field non-uniformity in the test specimen. The specimen design is sufficiently simple that a closed-form expression for the strain-displacement relationship has been successfully developed.     

使用超声估计肌肉疲劳的初步研究

表面肌电信号把神经肌肉活动和肌肉收缩联系起来，已被视为一种估计肌肉疲劳比较客观的方法，但也存在一些不足。另一方面，超声已广泛应用于医学诊断和研究，在骨骼肌方面也有不少研究报道，但还未见文献报道超声用于肌肉疲劳的估计。本文介绍一套自行开发的新的同步连续采集B超图像、力矩和肌电信号的采集系统，并利用它对肱二头肌的肌肉疲劳进行了估计。试验表明在30秒的肌肉疲劳过程中，肌肉厚度会以非线性的方式增加。     

Characterization of strongly interacted multiple cracks in an infinite plate

Based on the Kachanov method and the alternating iteration technique, a new method is proposed to deal with the problem of the strongly interacted multiple cracks in an infinite plate. Unlike the Kachanov method which neglects the interaction of the tractions of the non-uniform components, the tractions of the non-uniform components on the surfaces of cracks are considered through the alternating technique. The accuracy and efficiency of present method are validated by comparing the results of two collinear and two parallel overlapped open the cracks obtained by the present method with those of the exact solutions, the results of the Kachanov method and the alternating iteration technique. Applications of present method in solving sliding close crack problems and evaluating the plastic zones demonstrate the versatility of present method.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

稀土复合变质对新型铸造热锻模具钢组织与性能的影响

研究了稀土复合变质对新型铸造热锻模具钢（CHD钢）组织与性能的组织。结果表明，稀土复合变质能细化晶粒，并且随着稀土量的增加。细化效果明显；加入适量的稀土复合变质后，夹杂物数量明显减少，夹杂物趋于球化并均匀地分布在钢中，形态和分布得以了改善，向钢中加入稀土进行复合变质，能促进贝氏体、奥氏体和位错亚结构的形成，细化马氏体板条。当残留稀土含量为0.02%时，CHD钢的硬度、强度变化不大，断裂韧性（KIC）和疲劳裂纹扩展门槛值（△Kth）有所提高，冲击韧性、延伸率、断面收缩率提高了近一倍，抗热疲劳性能也最好。     

儿童易疲劳与血清中微量元素含量的相关性研究

测定了1562名儿童(其中包括153名易疲劳儿童)血清中Zn、Fe、Cu、Ca、Mn和Pb的含量。研究发现,易疲劳儿血清Ca含量(84.4±12.5μg/mL)显著低于对照组儿童(88.5 4±13.4μg/mL),P<0.05;Fe含量(1.094±0.22μg/mL)显著高于对照组儿童(1.07 4±0.22μg/mL),P<0.05;Mn含量(0.040 4±0.035μg/mL)非常显著高于对照组儿童(0.035 4±0.013μg/mL),P<0.001。